Autowatch Ghost Immobiliser Installation
The Ghost is the UK's most advanced aftermarket immobiliser for CAN buses. It's subtle, doesn't have key fobs or LED indicators and is hidden within the wiring of the vehicle.
The user can also disable the system for a short period of time by using Transport Mode when renting out their vehicle. immobiliser ghost will walk you through the process of installing an Ghost immobiliser.
Professional Installation
The Autowatch Ghost immobiliser is a modern security device that guards your vehicle from hacking, key cloning and relay attacks. The system connects directly to your car's ECU and is protected by a unique PIN code of your choice. It is undetectable by thieves using diagnostic scanners and other advanced methods. It cannot be disabled using circuit cuts.
The system is simple to use, however it is essential to have a professional installation to ensure a secure and secure connection with your vehicle's ECU. A Thatcham-approved installer can help in the installation and programming of your Ghost system. They can also recommend a tracking or alarm system to complete the protection package for your vehicle.
To avoid the accidental deployment of short circuits or airbags To avoid an accidental deployment of airbags or short circuits, the installer must remove your battery. When the battery is disconnected, the installer can safely begin working. Basic hand tools are helpful for securing connections with precision, while a multimeter can be used to verify electrical values and safety. Insulation tape and cable tie are vital to secure connections and keep wiring tidy. The Ghost Immobiliser user's manual will give specific instructions that are specifically tailored to your specific model.
It is important to choose an area for grounding that is free of paint or debris during installation. The installer must ensure that the immobiliser's H and CAN L wires are connected to the appropriate ports on the vehicle's ECU. The wires can be plugged in or soldered depending on the model. To ensure a secure and long-lasting connection it is recommended that you choose a top-quality plug.
Once the install is complete Once the installation is completed, the customer can enable after the installation is complete, the customer can activate Transport Mode. This allows the vehicle to be used by valet parking or mechanics without needing to know the pin code. The user must press the icon for service on the dashboard five times within 2 seconds. Once this is done the system will verify with 5 indication signals.
The Autowatch Ghost 2 is a highly efficient immobiliser that's TASSA certified and Thatcham approved. It's a smart option for anyone who regularly rents out their vehicles on platforms like Turo. An immobiliser can cut down on insurance costs, since it decreases the likelihood of theft.
Getting Started
If you're seeking a solution to protect your vehicle from thieves it is best to go with an autowatch ghost immobiliser. The device stops your car from starting when someone copies or steals your key. It's possible due to its advanced technology that stops the engine from starting until the right PIN code has been entered.
The device connects to the vehicle's bus system CAN, allowing direct communication with the ECU. It uses existing buttons on the dashboard and wheel to create a unique sequence only you can identify which makes it impossible for anyone else to start your vehicle. This is the ultimate security system that will safeguard your most precious possessions and will ensure its value should you decide to sell it in the future.
Installing a ghost immobiliser is an easy process, however, it is crucial to follow the directions carefully to avoid electrical issues and system malfunctions. First, you must locate a power supply of 12V and a solid grounding on the chassis of your car. Then, you'll be able to begin connecting the wires to the immobiliser. Use high-quality connectors, and soldering techniques to ensure a solid connection. Also, ensure that you cover the connections with heat shrink tubing and insulation tape to shield them from electrical short circuits and other issues.
After the wires have been connected, you can reconnect the battery and turn on the engine to test the function of the immobiliser. Once you have verified that everything is working correctly and you are satisfied, you can place the immobiliser in a secure place inside the vehicle. Be sure to hide it well to ensure that thieves cannot tamper with it.
The Ghost 2 immobiliser has been TASSA (Tracker and Aftermarket Security System Association) which means it is a top-quality deterrent to car burglars. It is a superior defense against key cloning, hacking, and relay attacks, and cannot be disabled without knowing the code. The device is easy to use and can be set to a service valet setting so that your vehicle won't be activated if you take it to an MOT or for servicing.
Wiring
The Ghost Immobiliser, a cutting technological security system, has been designed to stop theft of vehicles. It communicates with your vehicle's ECU and directly connects to its CAN bus. Contrary to other aftermarket systems which require the removal of circuit components, the Ghost Immobiliser doesn't interfere with the factory settings for your vehicle.
It's also undetectable to thieves using diagnostic scanning devices. The system does not send or receive radio frequency signals and instead uses CAN data for communication with your ECU. It also doesn't require modifications to your current key fobs.
Enter your sequence for disarming (either two or one buttons) and then switch on the ignition of your vehicle to activate Ghost Immobiliser. The indicator will flash twice to verify that you've entered the correct code. After this, you can start your vehicle and leave safely.
Once installed, Ghost Immobiliser protects your car against hacking or key cloning, while also protecting its value. If you ever need to surrender your car to valet parking or for service, the Ghost Immobiliser can be temporarily disabled in Transport Mode.
You'll require a continuous power source (12V) as well as a grounding source to complete the installation of the Ghost immobiliser. Be sure that both are well-insulated and able to be touched. Cable ties are also recommended for bundling and secure the wires. This will reduce the possibility of theft by thieves. Make sure you double-check the location of these points to avoid mistakes and mark them with an adhesive or label. It's important to inspect all connections for signs wear and tear. Loose connections can lead to problems with the system, so be certain that they are securely fixed and well-insulated. Make sure to test your Ghost Immobiliser after the installation is completed. This will make sure that the unit functions properly, and that all connections are secure and insulated. If you encounter any issues, make sure to address them immediately.
Testing
The Autowatch Ghost Immobiliser is a cutting-edge vehicle security system that integrates seamlessly into your car's ECU to stop unauthorized engine start. The innovative technology it uses protects your car against hacking, key cloning, and other typical tactics thieves employ to steal cars. The Ghost works in conjunction with existing tracking and alarm systems to provide the best security for your car. The Ghost's unmatched features, combined with its secluded design makes it a preferred choice for drivers who love cars and security-conscious drivers.
In order to ensure that the Ghost Immobiliser is properly integrated the Ghost Immobiliser, it is essential to follow all steps of the installation procedure. Check the wiring diagram for the vehicle to help you locate and connect the wires. You'll then need to identify the grounding and power sources. Once you've located them, you'll have to mark them to make them easy to identify during installation. It is essential to use top-quality materials and tools. Hand tools are essential to help you make precise connections. A multimeter will check electrical values and guarantee safety. Cable ties and insulation tape can help keep connections neat and tidy. A Ghost-specific user's manual is also available.
Before beginning the installation it is important to test the system by entering the PIN code and then starting the vehicle. This step will confirm that the immobiliser is working as intended, preventing unauthorised vehicle starts. It is recommended to complete this step regularly as part of your regular inspections of your vehicle to ensure that the system is always functioning properly.
After the installation has been completed, you are now able to start driving your vehicle with confidence. The Ghost will guard your car from potential car thieves. It will ensure that no one will take your car away even if they don't have the correct PIN code. The Ghost can also be paired with a tracker that is approved by Thatcham to detect any attempt to steal or tamper, allowing you to locate your vehicle in the event of it being stolen.
The Ghost can be used on a variety of vehicles and is compatible with all major manufacturers. Monty's Locksmith can help you secure your vehicle with this innovative device. Contact us today to learn more about our services and installation options. We are a TASSA Registered installer This certification ensures that we adhere to strict standards and procedures for installing our products. This reassures customers, insurers and law enforcement agencies that all installations are performed safely and correctly.